Wireless 4G single-path signalling with unrivalled management tools.
Our single-path signalling solution utilises a 4G Radio path or a LAN path to signal an alarm. The Radio variant also comes with a standby SIM as a backup to safeguard your system. Both SIMs operate on an independent network from the other for total resilience. DigiAir Pro 3 is also compatible with CSL Live and the My Base App.
As standard, the device is triggered by removing or applying zero volts to input terminals 1-8. No external pull-up resistors will be required. This is usually achieved via the digital communicator outputs of a control panel.
If you need to use a positive applied/removed, you can toggle the pin bias via the MyBase app or contact technical support so that they can amend the bias of the device.
Once the device is powered-up, you should see activity on LEDs 1, 2 and 3. When the device has commissioned, all 3 LEDs will go green for 5 seconds. The device will then reboot.
Once the device has completed its commissioning process, only LED 3 (device status) will be active whilst in Quiescent/Normal state.
You can also check the status of your device on the My Base App.
Both outputs can be configured as either N.O or N.C as required.
Output 1 is defaulted to indicate a total path fail condition to the control panel (but it can be reconfigured to indicate another path failure type).
Output 2 can be used to indicate a path fail condition or be used as a manual trigger.
To make any amendments please use the MyBase app or contact technical support.
Your device will come pre-configured without a panel connection type (pins only). To enable the serial connection to a control panel, go to My Base and select the panel type.
If you are not receiving signals, make sure you have completed the panel programming steps detailed in the panel guide for that particular control panel. The guides can be found online - Click here
As standard, the device is triggered by removing or applying zero volts to input terminals 1-8. If you are using a positive applied/removed to trigger the pins, you will not see any pin alarms in the alarm log until the bias of the device has been changed.
To change the input from negative removed or applied to positive removed or applied, change the pin bias via MyBase under the “Hardware" menu and use the A+ terminal instead of RTN.
Alternatively, please contact technical support for assistance.
You can add a panel profile via My Base under the “Hardware” menu and select “Edit Panel”. Please note you only need to set panel 1 (please leave panel 2 blank).
If you are not sure which panel profile to select, please search the panel guide for your specific panel on the installer zone as the guide will confirm which panel profile you need to select. The guides can be found on online - Click here
The My Base App is a self-service management platform for the newest generation of CSL devices. For DualCom Pro, Pro 2 & Pro 3 devices. You can check your signal strength, request regrades, send test alarms, view availability graphs, edit panel profiles, upgrade firmware and view alarm logs.
You can check the signal strength of the radio path on a commissioned device via the My Base App. Alternatively, when in the quiescent/normal state, you can press button A to toggle to the connectivity menu. Once there, LED 1 will show you the signal strength. We recommend a solid green LED (40% or 4/10).
Resetting your password will restart the multi-factor authentication process and resolve most issues with logging on. If you’re not receiving an email or text with your one-time access code you’ll need to call CSL Technical Support to update your contact details, please call +44 (0) 1895 474 444
Here is a list of commonly used authenticators approved by CSL:
For security, multi-factor authentication (MFA) is now required to use the My Base App. MFA drastically increases security on our platform and requires users to authenticate themselves via their username/password and with a time-limited code (each code expires after 60 seconds). This code is obtained via an Authenticator App, email or SMS. New authentication is required once every 30 days; if the user logs out or if we update CSL Live.
How it works:
If you have any issues with the steps above, resetting your password will restart the authentication process. If the issue persists and you require support, call CSL Technical Support on +44 (0) 1895 474 444.
Once you've installed My Base from your applicable App Store, please visit the CSL Website to register for a My Base account https://www.csl-group.com/uk/my-base-app/.
For security, we’ll contact you in order to authorize your request and set the appropriate permission levels for your My Base account. Once approved, we’ll send you your login credentials.
Need Support? Call CSL Technical Support on +44 (0) 1895 474 444.